![tbs discovery pro manual tbs discovery pro manual](https://cdn.mos.cms.futurecdn.net/sPuT478MrRDYaypW2oMkBb-320-80.jpg)
- #Tbs discovery pro manual manual#
- #Tbs discovery pro manual upgrade#
- #Tbs discovery pro manual full#
It now supports GPS to help navigation and a new range of TBS telemetry modules to take your FPV experience to the next level. There is no way around this - unless with smart batteries - the system cannot know how much capacity the battery has - you need to tell it. TBS CORE PNP PRO The all-in-one FPV power supply and flight OSD Revision The TBS CORE PRO is the progression of our CORE PNP system.
#Tbs discovery pro manual full#
Or you leave it at the lower setting (not leveraging the full capacity of the larger battery).
![tbs discovery pro manual tbs discovery pro manual](https://cdn.3dforprint.com/modelos/4024/tbs-discovery-pro-gimbal-platfom3.jpg)
It’s used to calculate when FS needs to kick in(and some other things), so yes, you will need to adjust it when you switch from a larger to a smaller battery. i am assuming you are referring to the battery capacity setting where you enter the mAh value. Config in Ardupilot (via missionplanner) that you doĪnd on the battery setting.Setup of channels/pwm values being transmitted by your RC transmitter.That represents a digital input.The flight mode change is influenced by two things: Pin will instead be a digital input if it is assigned to a parameter The 6 possible pins are available for PIN variables as pin numbers 50 toīy default, the pins are digital outputs as outlined above. If the servo function is being “mirrored” to a remote device, as in the case of a DroneCAN or KDECAN ESC, then in order to change the autopilot board’s corresponding output pin to be a GPIO, but allow the SERVOx_FUNCTION to still be assigned to the remote device, the SERVO_GPIO_MASK parameter can be used to assign the board pin to be a GPIO without affecting the SERVOx_FUNCTION assignment for the remote device. TBS Discovery Brushless Gimbal for Hero 3 by Nathan. If set to “0”, it remains a PWM output, unassigned to a function, and outputs that output’s trim value when board safety is not active. Go Pro, Hero 3, Remote Control Toys, Tbs, Fujifilm Instax Mini. Instead of BRD_PWM_COUNT being used, the individual SERVOx_FUNCTION parameter is merely set to “-1”. Visit our Contact Us page for more support information. In addition to the service information available in the owner's manual, you can contact the designated Product Support staff for your category of product.
#Tbs discovery pro manual manual#
TBS DISCOVERY and TBS DISCOVERY PRO owners will enjoy the ability to add larger props and higher cell motors to get the endurance or long range juices going. Find the manual or exploded parts view for your favorite Spektrum transmitter or accessory below.
#Tbs discovery pro manual upgrade#
In firmware versions 4.2 and later, the method for setting a PWM/SERVO/MOTOR output to be a GPIO function is changed. TBS DISCOVERY / DISCOVERY PRO ENDURANCE KIT High speed and endurance upgrade for the TBS DISCOVERY quadcopter platform. This can alternatively serve as SBus out by setting the Servo connector on the 14 connector servo rail). RSSI input pin on the SBUS-out connector (the bottom pin of the 2nd last Virtual Pin 103: RSSI (Received Signal Strength Input) input pin It has 3:1 scaling, allowing it to measure up to 9.9V. Measurement of the servo rail voltage made by the IO board within the Virtual Pin 102: Servo power rail voltage. Usually used for analog airspeed, but may be used for analog This has 2:1 scaling builtin, so can take up to 6.6v analog Virtual Pin 15 and ADC 6.6V connector Pin 2: analog airspeed sensor May be used for second sonar or other analog sensor. Virtual Pin 14 and ADC 3.3V connector Pin 2: This takes a max ofģ.3V. May be used for sonar or other analog sensors. Virtual Pin 13 and ADC 3.3V connector Pin 4: This takes a max ofģ.3V. Provide the HWSTATUS.Vcc reading that ground stations use to display 5V Virtual pin reads the voltage on the 5V supply rail. Virtual Pin 4 and (No connector Pin): VCC 5V rail sensing. Virtual Pin 3 and Power connector Pin 3: power management connectorĬurrent pin, accepts up to 3.3V, usually attached to a power module Management connector voltage pin, accepts up to 3.3V, usually attached Virtual Pin 2 and Power connector Pin 4: power This section lists the analog pins available on the Pixhawk.